When I get stressed out . . .

 . . . I get out my pencils, brushes and 1 Shot paint
and do Monsters !

Mr. Clean . . .



I like 'em functional.  This build impressed me with it's attention to detail.  Handmade goodies that probably work and function as stock.  So many guys try too hard with weird-ass funky shit that's just gross and stupid.  That makes builds like this one all the more impressive in my book.  I'd just like to fire this up and go for (quote from Indian Larry) . . . "A Lap Around Manhattan."

This is cool . . .

Reminiscent of the "clubber" type custom of yester-yore . . .

The flipped up white bobber chopper . . .



I don't know who built this chopper . . . but, I kinda liked it.  Once the guy gets his brake hooked up, and a couple other little things - I believe it's gonna be a bitchin' ride - and a real show stopper !
I suppose the flipped up rear fender - you could take(or leave it) - I liked it . . . the chromed frame and swingarm was highlighted with black (castings shown chrome).  SU Carb, Tank, Shocks, Paint, Bars . . . lot of unique pieces.  It was just cool - even with floorboards.  
Spoked a 1/2 brake front to a steel drop-center . . . just bitchin' . . .
Sissy Bar, Pipes . . . ZOOM IN - all kinds of neato stuff.

 Ricky drove up from Kansas City to hang around a couple days - and go check out the Donnie Smith Custom Cycle Show in St. Paul.  This show and swap is a great way to get the juices flowin' for ideas and inspiration - and he wasn't disappointed.  Neither was I . . .

Hey, give me a break . . .

I was just learning . . . still trying . . . When Spina looks at my striping, sometimes he likes it - sometimes not.  He'll ask me, "Who striped that?  Stevie Wonder?"  Answer is D.

Ol' Yellar in the Mojave . . .


Spina built and painted many Roth Trikes.  Back in the old days . . . on a run !

Ted's S&S Flywheels . . .

Big Noot got 'em all true for us while I was out fartin' around in Vegas when I shoulda been workin' on people's stuff . . . damn kids with no work ethic anyway . . . (NOTE: S&S don't use locks)

Flake, Striping, Leaf, Airbrush, Clear, Buff . . .





I was watching Spina paint a fairing . . .
1. Clean primer with alcohol and Windex before sanding.
2. Paint silver flake, mask flames, spray with Tangerine
3. Outline Flames
4. Stripe and Leaf top
5. Airbrush Leaf
6. Clear & Buff
A bit more process than that . . . but, you get my drift.  You dig?
In the sun - this sucker pops Wowza Morty !

Bad Bearing on 6 Speeds . . .

 My friend Bob noticed his 2007 was leaking oil back by the transmission.  It continued leaking and it was coming out more and more all the time . . . He thought it was just a bad seal, but the bearing was missing some balls (actually missing 2 complete ball bearings (he popped out 4 more later) Where did the ball bearings go?
 Bearing (8) and Seal (15)
 The bearing race was badly pitted and breaking away . . .
Bearing is H-D Part No. 8967. (FAG Bearing) If your trans starts leaking, you'd better check it out . . . He asked the dealership how many they had changed . . . They said, "A lot ! " . . . it's usually on a motorcycle with about 28,000+ miles . . .

HOT ROD Magazine 65th Homecoming !

Wish I could go see . . .
Hemi Under Glass
Mooneyes Dragster
Mickey Thompson's Challenger
Ed Iskenderian's T-Roadster
It's all at the HOT ROD Reunion this weekend in Pomona, California
They are bringing back all these cover cars from all the years back . . . Spina is hosting the pin-striping jam,
See more about the show at: Wally Parks NHRA Motorsports website !

You really ain't nothin' . . .



. . . . without nice paint.  Flat Black, Black, Rust . . . It just ain't finished without a bitchin' paint job.  It's where a really good build just ends up like everybody else.  It's just too easy nowadays to get online and buy shit . . . This rod - "The Iron Orchid" is so freakin' cool.  It's a true build - A true custom rod . . . becoming a lost art. 

Camshaft Endplay TECH

The factory (H-D) says .001 to .005 specifications.  I think that's too tight.  Big Noot (and myself) have seen plenty of "blued" cam shims and thrust washers.  These new cams (like Andrews, etc.) are made from a very low porous steel which can grow more - requiring more end play. Andrews says, .008-.012.
Always follow the specific instructions for your particular 
aftermarket camshaft.
1. Always check cam shaft end play with gasket and
cover fully tightened to torque spec.
2. Make sure there are no burrs on thrust washer.
3. I always "time" cam and breather
just the way in will run in engine.
4. Move cam towards gear cover (away from case)
5. Feeler gauge between thrust washer and cam shim.
6. Check at 180 degrees (rotate assembly and check again)


Mikuni 38mm SOLD



I bought this new from Sudco.  Jetted for Ironhead Sportster.  These also work on modified Yamaha TT500 or other 4 stroke singles.  $80.00 (Free Shipping).  Includes new throttle cable.

Motorsport Petcock SOLD


Rare, race fuel valve for screw-in tanks.  Cut the reserve to whatever length you want (need gas in 20 miles or need gas in 2 miles !)  The red "junkyard marker" will come off.  $40.00(free shipping)

CV Carbs on Pans & Shovels . . .

This guy Tom White is a real sharp dude writing programs and using a milling machine.  He manufactures a neato set of brackets that bolt to the heads of pans & shovels, so you can run a CV carburetor if so inclined.
he also has lots of other trick goodies . . . all made at TT Cycle, Belknap. Iowa !

Who needs Sudoku . . . ?

 . . . or crossword puzzles to exercise the mind . . . just learn to spoke wheels.

Cedar Rapids Swap



Terry Noth gave me an original K-Model Parts Book (with an XR-750 supplement inside)  Terry has been on this blog before . . . and it's always a trip to chat with him about Ks, KRs, KHKs, WRs . . . Sportster Strokers . . . it runs deep is his blood.  A total race builder who has built many many motors.
However, the swap meet was kinda a bust for me . . . I couldn't believe some people this year that you'd give them the opportunity to purchase a $100 part for $50 and they'd offer $20 . . . WTF ????

PS. Great to hang with Jeremiah, Pete, Dave, Papa Clutch, Michael, Steve . . . and all those CR party people and their gals I'm lucky enough to know . . . See ya'll real soon !  -Noot

Morty "The Official Shop Cat" says . . .


" I'm gettin' too old for this shit . . . we need a dog back there."  NO MORE POSSUM UNDER THE SHED.   But, now he's on the pink-stuff 3 times a day . . . again.

Carter & Franky


Left Side Timken Spacer

If you get your left side case all assembled (bearings pressed) and you find there's a little too much end play...... you can surface grind a small amount off your center spacer.  Some look like this (others are completely round with "timken" stamped on them).  If it's too tight (you need a thicker spacer, because the bearings are smashed against the races).  That's why the instructions are so strict on using the supplied spacer with your bearing kit, since all the tolerances are set up for that particular combination of bearings and races.  When you install your pulley (or compensating sprocket) it could take up a slight amount of end-play, so you need to take that into consideration too.  It's pure luck any of these garage builds work as good as they do with so much shit that could happen to just ruin your day !  Hey, why's my motor making these squealing sounds ???????

Poor Man's Polished Crank . . .






How to polish your crank and get professional results:
1. Cut your (600 grit) to journal width (add lube if desired)
2. Tape it tight to journal
3. Use leather or rawhide
4. Spin emery paper (I use 3M wet/dry) for about 30 secs.
5. Remove and inspect
6. Repeat with 800 or 1000 grit as desired
This method leaves a beautiful, polished surface for your new bearings and is ready for plasti-gage measuring - which is highly recommended (even after bore-gage measurements) This particular crank measured almost perfect - but, it had oil scoring, which was removed after this procedure.

Happy Birthday Big Daddy !

I never got the chance to meet him . . . but, I get to hang with a few who knew him well.  The stories just flow . . . and they are so proud to tell them.  Roth was a true giant.  His legend still stands.  His fiberglass creations were first shunned by the industry . . . (now a guy with a glass '32 Ford thinks he has a real one and wins first place at the show !) Roth took a lot of things and made them cool - or made them cooler - and made them so we could have one too.  He gave away all his secrets, all his findings, all the stuff he worked so hard to create - he gave it all away - so we could all be cool.  Long Live "Big Daddy" Ed Roth.

The highest RPM cam I've found . . .


If you want a camshaft that still performs at high rpms . . . you can't get much better than an Andrews Z Grind.  4000 to 75,000 rpms Wowza !  Typo?  Possibly?

Fits: K & Iron Sportster

Anyone need a set of rebuilt connecting rods?  $40.00
Straight, Sunnen Honed, Good Wrist Pin Bushings.
Good for 7000 rpms all day long . . .