FXR Show at Buffalo Chip Crossroads

I've attended this show the last few years....and it brings a good mix of hot stock to full-out-customs. 

Scenic, South Dakota

My ride in for a delicious Buffalo Burger and a Budweiser !
They are sooooo good.

Served from this old church . . .

The Tanaka Trading Post

I told the rancher(owner) who runs the place, he should have the movie loop of Dances with Wolves playin' all day - and he replied, "That's a good idea !" 

Head Onto The Highway - Lookin' For Adventure....

After gettin' through Iowa (sunshine) . . . the minute I hit South Dakota on Hwy 46(Beresford,SD) you could see the rain ahead.  Rats.

Above: The Dug Out Bar in Tripp, SD has ice cold _______.

Never seen it this muddy up here . . .

 

My rain suit went on at the Lake Francis Case lookout over the Missouri River.  I've rode up through those hills before when it looked like this - and you can't see crap.  I had this all shined up when I left . . .

Fog cleared . . . Sunny skies ahead !  Top gear - 75mph, leanin' back on the pack, one hand, panhead up sweeps in your ears singin' the sweet sounds - Nothin' better.  Hwy 44 thru Pine Ridge . . . . nobody out here but me . . . and the real native Americans. 

SD44 is well marked - and one of the most beautiful roads in America.  Rolling hills (and all is green this year from solid rainfall).  I stopped at every gas pump.  Never had to use my aluminum(reserve bottle) - and most fills took 1.5 to 1.7 gals.  Ave 40+mpg.   This was my 6th trip on this bike - and it runs strong as ever - No chain adjustments needed - and I think "it made oil" ???? as it seemed to be a bit higher than when I left home???  What the heck ?

I've been to The Wagon Wheel 20 times now . . . my 20th Run through this area.  It feels like home, and the friends I've met, I see every year, from bar owners to station owners.  Many locals who've helped me out over the years - great to see everyone again. My old panhead in a sea of dressers really gathers attention with other travelers.  Small gas tank, rigid - I get lots of respect, and meet so many good folks riding this motorcycle - I feel fortunate to travel on the old school customs of years ago, and be healthy enough to ride the damn thing ! 

This little area in the bottom of the Badlands is my spot.  There's no place like it on the planet.  I like to stop every year and just sit.  The earth is a beautiful place to live - I just wish more people would appreciate and respect mother earth.....

My trip to the rally every year is much more than the party, bikes, etc . . . but after a few of these stops - I'm ready to get down - Only about 100 miles to go . . . (gone 500 miles now)

What the heck, Let's Party !

. . . and party I did - right after I hooked up with these two crazy bloods.  The Dungeon Bar is where shit gets done.  The girls didn't know what to think of us . . .

 

 

Rear Pipe "Kink"

I think the factory bent the last 15" of rear pipe inward to keep it from hitting the dirt on right-handers, when leaned way over....and the shocks would compress, bumps, etc. 

The Supersuckers

I like this song.  It's about a guy Goin' Back To Tucson and he doesn't really want to go back - but he does anyway.  Then he leaves again.  They've recorded with Willie Nelson, Steve Earle and many others - and toured with Motorhead, The Ramones, New York Dolls and they even played on The Tonite Show. 
Great band . . .

Gaskets

I buy 10 packs of REAR panhead baskets - and make them into FRONTS !  I use this old, original (white cardboard-type) front panhead base gasket as a guide.  I lay it on a rear gasket, and trace the edge - then cut off the edge.  Saves me money buying (2) 10 packs of fronts & rears . . .

I like the thick D-Ring cover gaskets, the "firm.dense" style for the dampening pads, Fire-Ring style for the head gaskets, and the heavier Athena brand base gaskets.  You can adjust your base/head gasket thickness when determining your piston height at TDC in the cylinder.  I try to keep a variety on hand.  I have a "gasket addiction" and I've saved all types of gaskets over the years.

I have multiple, flat containers (as above) with all types of gaskets for 900 Sportsters, K Models, 45s and Panheads . . . and a quite extensive collection of 4 speed transmission gaskets, seals, etc. Also extra bushings of all types.  It's really sickening . . .

I've got gaskets they don't even make anymore - and when I'm down to my last one, I get all worried and panic . . . The extra-thick XLCH tin cover primary gaskets are awesome.  I gave a couple away to a buddy this summer for payment of a shared booth space - and I still have like 7 left . . . but I'm still thinking about it !  I've got problems . . .  But hey, those old-time, super thin oil pump gaskets that shrink up over the years (and you have to put them in water to expand them) are the best.  The new ones are too thick - and those white mylar plastic things are junk.  Sometimes I just open up everything and take a mental inventory again.  I have gaskets all over the living room floor and my wife thinks I'm a kook with all this stuff.  But I just love it . . . Anyone need a gasket? 

Short Stroke

Wrench & Repair

On side valve motors, it's easy to see how cam/valve timing and ignition timing work, and understand what's actually happening in the motor (with the heads off) What position the piston is in - Where the valves are on each cylinder, in relation to which cylinder is firing.  The Harley 45s are a great learning tool to educate a person how engines work, and what makes them work.  A mechanic has to understand how a motor works in order to correctly diagnose issues.  Myself, personally, after all this education, and thinking, etc . . . I still have a difficult time troubleshooting problems, which is the true test of a good Wrench.  You can be a great engine builder, a great machinist, etc., but a good Wrench is a difficult title to achieve.  It's probably the reason most of the oldest mechanics are the best Wrenches . . . they've seen it all and 'been doin' it the longest.

Orange & Black

Morris Mags

Are these real magnesium?  Some are - some aren't I believe?  A couple different versions.  The can make any bike look good - especially the "ready for a street fight" lookin' shovelheads !
(Click Photo for LARGE View)

Preparation

I've decided to run this bike to Sturgis this year.  It will be it's 6th trip in 7 years.  Fuel every 50-70 miles (depending on towns with gas stations).  If I'm in a hurry, I just leave it running, swipe a card, and 1.5 or 1.6 or 1.7 gallons later . . . I'm rollin' outta there !

I checked all the fluids (really clean !), did a "nut & bolt" check with all the wrenches on the entire bike.  I took the primary cover off (no belt dust) and just looked over the belt, checked a couple things, everything good.  I run a Diamond chain, and I shot 3 kinds of lube all over it - then chain wax at the end.  Don't really like chain wax 'cause it's white, and looks like shit - so I wiped most of it back off.  They throw out little cans of chain lube at the bike shows (I don't know why, since most run belts anyway?) so I usually get one for the trip home.

I just ride this thing pretty normal - and nice.  It runs the old style "roller" lower end (no Timken) and it's just been a great engine.  No burnouts, No poppin' the clutch, No powershifts.  It'll do a steady 75mph all day long - and last time I went on this trip I rode it almost 750miles in one day.  Pretty good for a '52 rigid frame chopper. 

Brake fluid is full and clean.  It's my only brake, so it'd better work, right?  Tires good, check the spokes, axle nuts, brake nut, axle adjusters . . . and my chain guard is spring/bolt mounted (like factory) so my oil tank don't crack, and stuff doesn't break - it's worked good so far.

This Super E has just been the best.  I can't even remember what jets I run, but a suspect a 29.5 and a 70 or 72 Main?  I've had the carb for years.  I sanded the body for polishing, but then left it as is...since it looks cool.  We've been through a lot together, on multiple bikes, multiple miles.

My ol' friend Lil' Joe (from Las Vegas) molded the frame, tank, everything . . . and painted it.  It has took direct hits from the biggest rocks, and some huge bugs - and never chipped.  The bondo has not cracked (partially due to Jeff Wiley's dynamic balancing of my stock flywheels).  Lil' Joe PAINT with Noot WRENCH . . . Wish me luck - but with the good Lord on my side, and a smile on my face, I'll try to see some sights and have some fun - and share it with you later.  Not everyone has the time or money to go on a trip like this - and each year I dedicate my run to those we've lost, and to those less fortunate - and try to spread some cheer to all I meet.  Respectfully, -Noot

I Guess If I Had An FXR . . .

 . . . I'd want one kinda like this !

Pan Cover Sealing

The Right Stuff gasket maker by Permatex is the best solution for sealing up your pan covers.  I put a small bead around the head, smooth it with my finger, attach the James gasket (I like the medium thickness dark gray ones), then smear a bit more (especially on the low sides - front and rear, then add the covers, maybe just wiggle 'em around a bit, line up the holes, add the D-Ring . . . then snug 'em down (starting on the low sides) evenly all the way.  Clean up the squeezed excess with Brake Kleen - then retorque after you run the bike some.  Best way I've found to seal 'em . . .

'48s Are Pretty Great

This is a '48FL I been workin' on for about 2 years.  We need an FL plumber-type intake manifold(3 3/8" length) and a Timer Head for those 2-piece points(like a Chevy 6 takes...) then we could run a good condenser, like a Blue Streak or Zenith.  A '48/'49 actually had a steel manifold that was welded and smoothed out, but a bit later cast manifold would work for now . . .

My Favorite Motorcycle

This ol' 52K is one of my favorite motorcycles I've ever had . . . but they sure are weird.  I mean what super genius came up with angled valves for better flow, and instead of angling the tappets - lets just angle the cam lobes - ground at 3 degree angle all the way around on exhaust and 1.5 degrees on the intakes???  What the heck?

I did have an old timer tell me that Sportster P grind cams work good in Ks and KHs . .  and they ran 'em all the time for racing.  I asked, "What about the cam follower rollers riding on straight lobed cams?  The wheels would just ride on one edge?  He said is did wear 'em out, but had less friction, like riding on a knife edge . . . and just for 20 laps around the track.  I've never tried it . . .

 . . . and  '52-'53 crank pins/right flywheels press in with a key to help lock it - and line up the oil hole. Save money on nuts, locks, and screws?  This actually ain't a bad system.  It came back with the Twin Cams.

TECH TIP: DC Carburetor Jet

The DC-11 is an oddball.  They say it's for an XLR, but the more I research, it's just a replacement carburetor for any of the other DC-6,7,10, etc.  Anyway, I've had one for years.  I took it all apart and compared with a bunch of other DCs...and I can't find anything different - except someone had silver soldered the #4 jet shut, and redrilled it smaller.  I replaced it with a standard #4 (which is .057 hole) My float bowl was leaking, so I took it back off to reseal...and I thought, "I should just put that smaller jet in, see what it does."  Well, I was surprised - after a few screw adjustments - this thing now rips !  That jet does nothing more but feed fuel to passage regulated by that fuel screw up above(on top) that should be adjusted 1 1/2-2 1/2 turns out(w/#4 jet).  Now I need to run that screw at 4 1/2 to 5 turns out.  I see there's a #1 Jet (.052) available.  Maybe try one in your own DC if you're crazy enough to run one...and see what happens.  Next time I take my bowl off, I'll get the jet drills and see what size it is for sure . . .

'54FL

Got this panhead running decent now.  I built a set of early heads (w/o-ring intake adapters).  Runnin' 1/8" oversize nitrite valves with cast iron guides.  Andrews springs set up to .550 travel and 1.340 installed height.  Andrews #1 low compression cam.  I like the Andrews #1 in my stock chopper 74", but in this 4 1/2" stroker 84"... with increased compression - I'm getting some pinging at low speeds, and in high gear when tryin' to get with it . . . I set up the heads for an Andrews B or Leineweber L3S - so changes can be made without more valve spring set-up.

How do you like this cockpit - all business !

I built this bike for vintage touring - trying to use all H-D parts, ie: frame, engine, tanks, sheet metal, etc.  Even if it had a dent, I still used it.  Original H-D USA over ___________. (well you know) I had a couple sets of aftermarket tanks, and they just didn't fit right - so I picked up these original 1954 tanks, dash plate and dash, all bought separately - and everything bolted right on - no shims and plenty of time left for an ice cold High Life !